MIMAKI JV5-320S Spécifications télécharger pdf (Page 212)

5 In Case of Trouble

5-20

∗∗∗∗∗ ERROR 16 ∗∗∗∗∗

MRL COMMAND

An error occurred in the control sys-

tem.

Transmit data that is compatible with

the command system supported by this

printer.

∗∗∗∗∗ ERROR 20 ∗∗∗∗∗

I/F BOARD 01

An error occurred in the control sys-

tem.

Turn off the power to the printer and

turn it on after a while. If the same

error message appears again, contact

your local distributor to call for ser-

vice.

∗∗∗∗∗ ERROR 20 ∗∗∗∗∗

I/F BOARD 02

An error occurred in the control sys-

tem.

∗∗∗∗∗ ERROR 20 ∗∗∗∗∗

I/F BOARD 03

An error occurred in the control sys-

tem.

∗∗∗∗∗ ERROR 20 ∗∗∗∗∗

I/F BOARD 04

An error occurred in the control sys-

tem.

∗∗∗∗∗ ERROR 21 ∗∗∗∗∗

I/F NONE

An error occurred in the control sys-

tem.

Turn off the power to the printer and

turn it on after a while. If the same

error message appears again, contact

your local distributor to call for ser-

vice.

∗∗∗∗∗ ERROR 23 ∗∗∗∗∗

HOST I/F

Timeout error occurred during commu-

nication between the host computer

and the interface board for IEEE-1394

connection.

Check that the cable is securely con-

nected to the host computer and inter-

face board. Also, check to see if any

error has occurred on the host com-

puter.

∗∗∗∗∗ ERROR 24 ∗∗∗∗∗

I/F INITIAL

An error occurred in the control sys-

tem.

Turn off the power to the printer and

turn it on after a while. If the same

error message appears again, contact

your local distributor to call for ser-

vice.

∗∗∗∗∗ ERROR 25 ∗∗∗∗∗

FULL-SPEED

An error occurred in communication

between the host computer and the

interface board for USB2.0 connec-

tion.

(Full-Speed mode connection)

Check that the host PC supports the

USB2.0 interface.

(Communication can be resumed with-

out changing any setting. However, it

is recommend to use the connection in

High-Speed mode.)

∗∗∗∗∗ ERROR 25 ∗∗∗∗∗

PACKET SIZE OVER

An error occurred in communication

between the host computer and the

interface board for USB2.0 connec-

tion.

Check that the cable is securely con-

nected to the host computer and inter-

face board. Also, check to see if any

error has occurred on the host com-

puter.

∗∗∗∗∗ ERROR 25 ∗∗∗∗∗

USB PROTOCOL

An error occurred in communication

between the host computer and the

interface board for USB2.0 connec-

tion.

∗∗∗∗∗ ERROR 25 ∗∗∗∗∗

USB ENVIRONMENT

An error occurred in communication

between the host computer and the

interface board for USB2.0 connec-

tion.

∗∗∗∗∗ ERROR 25 ∗∗∗∗∗

USB DATA

An error occurred in communication

between the host computer and the

interface board for USB2.0 connec-

tion.

Error message Cause Remedy

1 2 ... 207 208 209 210 211 212 213 214 215 216 217 ... 297 298

Commentaires sur ces manuels

Pas de commentaire