MIMAKI JV33-160 Spécifications Page 154
- Page / 202
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4-40
How to shake the ink cartridge
To prevent ink from leaking when you shake the cartridge, wear gloves and firmly cover the A part of the
upper surface of the cartridge and the B part of the bottom surface of the cartridge with paper towels. Then,
shake it more than twenty times right and left so that ink flows inside the cartridge.
Set the interval to display the warning message
Depending on the ambient temperature, set the interval to display the warning preventing color material settling.
1
Select [ROUTINE SETUP] of the maintenance menu.
(1) Press the key in LOCAL.
(2) Press to select [MAINTENANCE] and press the key.
(3) Press to select [ROUTINE SETUP].
(4) Press the key.
2
Press the key to select [Sub-
INK WARNING].
• If you shake it too strong, the pack inside may be damaged and it may cause ink leakage.
Therefore, perform this carefully.
• If the remaining amount of ink is less, ink in the cartridge cannot be beaten enough. Tilt the
cartridge until it becomes vertical.
• If you shake the ink cartridge too strong, it may damage the inside pack and it may cause
ink leakage. Be careful about it.
• When the cartridge is new, shake it before taking it out of bag.
• When the cartridge is in-use, be sure to wear the gloves, press waste close to the inserted
side and shake it.
• If the remaining amount of ink is less, tilt it until it becomes vertical, as you cannot shake it
enough in some cases.
• When you use MBIS, do not shake the eco case and the intermediate cartridge.
• Do not insert and pull out the intermediate cartridge as much as possible. It may cause ink
leakage.
• When you use sublimation transfer ink Sb52 or Sb53, the display interval of the message is
set to 72 hours in the initial condition.
• When you use sublimation transfer ink Sb51 or Sb60, this function is disabled (OFF) in the
initial condition.
A part
(the place to stick a
needle)
B part
(the slot on the
bottom)
Cover with paper towel firmly and shake ink slowly
Repeat
this
A part
ROUT I NE SETUP
Sub - INK WARNING<en t >
- MIMAKI ENGINEERING CO., LTD 1
- TABLE OF CONTENTS 2
- DISCLAIMER OF WARRANTY 8
- Requests 8
- FCC Statement (USA) 8
- Foreword 9
- Features 10
- Safety Precautions 12
- Warning for Use 13
- Precautions in Use 14
- CAUTIONS and NOTES 15
- Cautions on Installation 16
- CHAPTER 1 17
- Before Use 17
- Moving this machine 18
- Names of Parts and Functions 20
- Rear / Sides 21
- Operation Panel 22
- Media sensor 23
- Carriage 24
- Cutter blade and cutting line 24
- Capping station 25
- Connecting cables 26
- Connecting the power cable 27
- Inserting ink cartridges 28
- For Ink cartridge lamps 29
- Usable sizes of media 31
- Caution in handling of medias 31
- Menu mode 32
- CHAPTER 2 33
- Basic Operations 33
- User type 34
- Workflow 35
- Turning the power ON/OFF 36
- Turning the power OFF 37
- Setting medias 38
- Setting a roll media 40
- Pull out the roll media out 42
- I nput o f Med i aLeng t h 44
- MEDIA LENGTH =xxx.xm 44
- MED I A L ENGTH = 5 0 . 0m 44
- Setting the torque limiter 45
- Setting leaf media 46
- Notes when using media press 47
- Changing the printing origin 48
- Preparing Heaters 50
- Test printing 52
- Check before the 54
- Head Cleaning 56
- Drawing data 62
- Cutting a media 64
- CHAPTER 3 65
- List of functions 67
- Setting media compensation 69
- Press the key in the local 72
- Example of beading 75
- Setting print mode 76
- Setting scanning direction 78
- Setting Logical-seek 79
- Setting WhiteLay Print 80
- Setting drying time 82
- Setting margins 83
- Setting Priority 84
- Setting Auto cleaning 86
- Setting media detection 90
- Other settings 92
- List of Settings 93
- Initializing the settings 94
- Machine settings 95
- Setting the deodorize fan 96
- Setting Dryness feeding 97
- Setting Stamp 98
- Examples of Output 99
- Setting Test draw arrange 100
- Convenient use 101
- **** ERROR 120 **** 102
- ROOM T EMP LOW ( XX ° C ) 102
- **** ERROR 121 **** 102
- ROOM T EMP H I GH ( XX ° C ) 102
- Setting confirmation feeding 103
- Setting time 104
- Setting Unit 105
- Setting Machine name 106
- Setting Key buzzer 107
- Extension of Ink Expiry Month 108
- Displaying Information 112
- For the information displayed 113
- CHAPTER 4 115
- Routine Maintenance 115
- Maintaining 116
- Cleaning exterior surfaces 117
- Cleaning the platen 117
- Cleaning the media sensor 118
- Cleaning the media press 118
- Maintaining Capping station 119
- Replacing the wiper 121
- Prior to Pump tube washing 122
- Discharging Cleaning solution 123
- Washing of Head nozzle 124
- Check the follow 128
- Open the maintenance cover 130
- Filling up ink 132
- DISCHARGE & WASH 133
- Initial ink fill up 135
- Example of Pattern printing 137
- Setting Routine operations 142
- Other maintenance functions 148
- INK WARNING] 154
- Check message in Local mode 157
- Replacing waste ink tank 158
- Changing the ink 160
- Replacing the cutter blade 161
- Close the front cover 162
- Press the key 162
- CHAPTER 5 163
- Troubleshooting 163
- Image quality is poor 166
- Nozzle is clogged 166
- Ink cartridge warning appears 167
- Warning / Error Messages 168
- Message Cause Solution 170
- Error messages 171
- CHAPTER 6 175
- Appendix 175
- Machine specifications 176
- Ink specifications 178
- Sheet for inquiry 179
- Warning labels 180
- Function Flowchart 182
- INFORMATION 184
- MACHINE SET 2 184
- MACHINE SET 184
- MAINTENANCE 184
- To P6-14 186
- To P6-20 192
- From P6-18 194
- To P6-22 194
- OFF / 1 ~ 168 h 194
- MACHINE SETUP 198
- D201694-16-31012012 201
- FW : 5.3 202
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV33-160
(150 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.766 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels