MIMAKI JV33-160 Spécifications Page 23
- Page / 202
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1-7
Names of Parts and Functions
1
Before Use
Heater
Pre-heater /Print heater / Post-heater are equipped on the platen.
The Pre-heater is used for pre-heating of the media prior to printing to prevent rapid temperature changing.
The Print-heater improves the image quality in printing.
The Post-heater dries ink after printing.
Media sensor
The media sensor detects the presence of the media and the media
length.
This machine has a media sensor on the platen (in the rear).
• While the heater is on, the platen is very hot. When the front cover is to be opened or media is
to be replaced, lower the heater temperatures and wait until the platen temperature drops; oth-
erwise, you can get burned.
• When the media is to be replaced with a thin one, lower the heater temperatures and wait until
the platen temperature drops adequately. Setting a thin sheet of media while the platen is hot
may cause the media to stick to the platen or cause wrinkling or curling of the media.
• Set the media so that the media sensor located in the
rear of the platen is covered with the media without
fail. The media can not be detected unless it is
placed over the sensor.
Post-heater Print heater Pre-heter
Media sensor
- MIMAKI ENGINEERING CO., LTD 1
- TABLE OF CONTENTS 2
- DISCLAIMER OF WARRANTY 8
- Requests 8
- FCC Statement (USA) 8
- Foreword 9
- Features 10
- Safety Precautions 12
- Warning for Use 13
- Precautions in Use 14
- CAUTIONS and NOTES 15
- Cautions on Installation 16
- CHAPTER 1 17
- Before Use 17
- Moving this machine 18
- Names of Parts and Functions 20
- Rear / Sides 21
- Operation Panel 22
- Media sensor 23
- Carriage 24
- Cutter blade and cutting line 24
- Capping station 25
- Connecting cables 26
- Connecting the power cable 27
- Inserting ink cartridges 28
- For Ink cartridge lamps 29
- Usable sizes of media 31
- Caution in handling of medias 31
- Menu mode 32
- CHAPTER 2 33
- Basic Operations 33
- User type 34
- Workflow 35
- Turning the power ON/OFF 36
- Turning the power OFF 37
- Setting medias 38
- Setting a roll media 40
- Pull out the roll media out 42
- I nput o f Med i aLeng t h 44
- MEDIA LENGTH =xxx.xm 44
- MED I A L ENGTH = 5 0 . 0m 44
- Setting the torque limiter 45
- Setting leaf media 46
- Notes when using media press 47
- Changing the printing origin 48
- Preparing Heaters 50
- Test printing 52
- Check before the 54
- Head Cleaning 56
- Drawing data 62
- Cutting a media 64
- CHAPTER 3 65
- List of functions 67
- Setting media compensation 69
- Press the key in the local 72
- Example of beading 75
- Setting print mode 76
- Setting scanning direction 78
- Setting Logical-seek 79
- Setting WhiteLay Print 80
- Setting drying time 82
- Setting margins 83
- Setting Priority 84
- Setting Auto cleaning 86
- Setting media detection 90
- Other settings 92
- List of Settings 93
- Initializing the settings 94
- Machine settings 95
- Setting the deodorize fan 96
- Setting Dryness feeding 97
- Setting Stamp 98
- Examples of Output 99
- Setting Test draw arrange 100
- Convenient use 101
- **** ERROR 120 **** 102
- ROOM T EMP LOW ( XX ° C ) 102
- **** ERROR 121 **** 102
- ROOM T EMP H I GH ( XX ° C ) 102
- Setting confirmation feeding 103
- Setting time 104
- Setting Unit 105
- Setting Machine name 106
- Setting Key buzzer 107
- Extension of Ink Expiry Month 108
- Displaying Information 112
- For the information displayed 113
- CHAPTER 4 115
- Routine Maintenance 115
- Maintaining 116
- Cleaning exterior surfaces 117
- Cleaning the platen 117
- Cleaning the media sensor 118
- Cleaning the media press 118
- Maintaining Capping station 119
- Replacing the wiper 121
- Prior to Pump tube washing 122
- Discharging Cleaning solution 123
- Washing of Head nozzle 124
- Check the follow 128
- Open the maintenance cover 130
- Filling up ink 132
- DISCHARGE & WASH 133
- Initial ink fill up 135
- Example of Pattern printing 137
- Setting Routine operations 142
- Other maintenance functions 148
- INK WARNING] 154
- Check message in Local mode 157
- Replacing waste ink tank 158
- Changing the ink 160
- Replacing the cutter blade 161
- Close the front cover 162
- Press the key 162
- CHAPTER 5 163
- Troubleshooting 163
- Image quality is poor 166
- Nozzle is clogged 166
- Ink cartridge warning appears 167
- Warning / Error Messages 168
- Message Cause Solution 170
- Error messages 171
- CHAPTER 6 175
- Appendix 175
- Machine specifications 176
- Ink specifications 178
- Sheet for inquiry 179
- Warning labels 180
- Function Flowchart 182
- INFORMATION 184
- MACHINE SET 2 184
- MACHINE SET 184
- MAINTENANCE 184
- To P6-14 186
- To P6-20 192
- From P6-18 194
- To P6-22 194
- OFF / 1 ~ 168 h 194
- MACHINE SETUP 198
- D201694-16-31012012 201
- FW : 5.3 202
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV33-160
(150 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.162 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels