MIMAKI JV33-160 Spécifications Page 16
- Page / 202
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
xv
Safety Precautions
Cautions on Installation
Warning
Notes on maintenance
• It is strongly recommended to use the machine in a room that is not dusty. Set the Refresh level 2 or 3 when
the machine is to be used in an unfavorable environment. (P.3-29 "Setting of Refreshing")
• Keep the front cover closed even when the machine is not printing. If not, dust can accumulate on the
nozzles in the heads.
• Dust in the heads can also cause drops of ink to fall suddenly down on the media during printing. In such a
case, be sure to clean up the heads. (P.3-22 "Setting Auto cleaning")
• When cleaning the ink-station or the heads, make sure to wear the attached gloves. Further, when the
solvent ink is used, it is necessary to wear the attached goggles.
• Perform wiping (removal of dust and paper powder) of the capping station and wiper frequently.
Periodic replacement parts
• Some parts of this machine must be replaced with a new one periodically by service personnel. Be sure to
make a contract with your distributor or dealer for After sale service to ensure a long life of your machine.
CAUTION
A place exposed to direct
sunlight
On an inclined surface A place where temperature or
humidity varies significantly
• Use the machine under
the following
environmental
conditions:
• Operating environment:
20 to 35 °C
(68 to 95 °F)
35 to 65 % (Rh)
A place that vibrates A place exposed to direct air
flow from an air conditioner or
the like.
Around a place where fire is
used
- MIMAKI ENGINEERING CO., LTD 1
- TABLE OF CONTENTS 2
- DISCLAIMER OF WARRANTY 8
- Requests 8
- FCC Statement (USA) 8
- Foreword 9
- Features 10
- Safety Precautions 12
- Warning for Use 13
- Precautions in Use 14
- CAUTIONS and NOTES 15
- Cautions on Installation 16
- CHAPTER 1 17
- Before Use 17
- Moving this machine 18
- Names of Parts and Functions 20
- Rear / Sides 21
- Operation Panel 22
- Media sensor 23
- Carriage 24
- Cutter blade and cutting line 24
- Capping station 25
- Connecting cables 26
- Connecting the power cable 27
- Inserting ink cartridges 28
- For Ink cartridge lamps 29
- Usable sizes of media 31
- Caution in handling of medias 31
- Menu mode 32
- CHAPTER 2 33
- Basic Operations 33
- User type 34
- Workflow 35
- Turning the power ON/OFF 36
- Turning the power OFF 37
- Setting medias 38
- Setting a roll media 40
- Pull out the roll media out 42
- I nput o f Med i aLeng t h 44
- MEDIA LENGTH =xxx.xm 44
- MED I A L ENGTH = 5 0 . 0m 44
- Setting the torque limiter 45
- Setting leaf media 46
- Notes when using media press 47
- Changing the printing origin 48
- Preparing Heaters 50
- Test printing 52
- Check before the 54
- Head Cleaning 56
- Drawing data 62
- Cutting a media 64
- CHAPTER 3 65
- List of functions 67
- Setting media compensation 69
- Press the key in the local 72
- Example of beading 75
- Setting print mode 76
- Setting scanning direction 78
- Setting Logical-seek 79
- Setting WhiteLay Print 80
- Setting drying time 82
- Setting margins 83
- Setting Priority 84
- Setting Auto cleaning 86
- Setting media detection 90
- Other settings 92
- List of Settings 93
- Initializing the settings 94
- Machine settings 95
- Setting the deodorize fan 96
- Setting Dryness feeding 97
- Setting Stamp 98
- Examples of Output 99
- Setting Test draw arrange 100
- Convenient use 101
- **** ERROR 120 **** 102
- ROOM T EMP LOW ( XX ° C ) 102
- **** ERROR 121 **** 102
- ROOM T EMP H I GH ( XX ° C ) 102
- Setting confirmation feeding 103
- Setting time 104
- Setting Unit 105
- Setting Machine name 106
- Setting Key buzzer 107
- Extension of Ink Expiry Month 108
- Displaying Information 112
- For the information displayed 113
- CHAPTER 4 115
- Routine Maintenance 115
- Maintaining 116
- Cleaning exterior surfaces 117
- Cleaning the platen 117
- Cleaning the media sensor 118
- Cleaning the media press 118
- Maintaining Capping station 119
- Replacing the wiper 121
- Prior to Pump tube washing 122
- Discharging Cleaning solution 123
- Washing of Head nozzle 124
- Check the follow 128
- Open the maintenance cover 130
- Filling up ink 132
- DISCHARGE & WASH 133
- Initial ink fill up 135
- Example of Pattern printing 137
- Setting Routine operations 142
- Other maintenance functions 148
- INK WARNING] 154
- Check message in Local mode 157
- Replacing waste ink tank 158
- Changing the ink 160
- Replacing the cutter blade 161
- Close the front cover 162
- Press the key 162
- CHAPTER 5 163
- Troubleshooting 163
- Image quality is poor 166
- Nozzle is clogged 166
- Ink cartridge warning appears 167
- Warning / Error Messages 168
- Message Cause Solution 170
- Error messages 171
- CHAPTER 6 175
- Appendix 175
- Machine specifications 176
- Ink specifications 178
- Sheet for inquiry 179
- Warning labels 180
- Function Flowchart 182
- INFORMATION 184
- MACHINE SET 2 184
- MACHINE SET 184
- MAINTENANCE 184
- To P6-14 186
- To P6-20 192
- From P6-18 194
- To P6-22 194
- OFF / 1 ~ 168 h 194
- MACHINE SETUP 198
- D201694-16-31012012 201
- FW : 5.3 202
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV33-160
(150 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels