MIMAKI JV3-130SPII Spécifications Page 117
- Page / 142
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
- 5.27 -
Using the small amount of remaining ink in the 440cc ink cartridge
For the 440cc ink cartrige, when [NEAR END] or [INK END] is displyed some ink may
remain in the ink cartridge. At this time it is possible to use remaining ink by selecting the
amount.
• This function only supports 440cc ink cartridge which detecting [NEAR END]
or [INK END]. 220cc ink cartridge or [NEAR END] undetecting ink cartridge
are not supported.
• Even though this function is performed, [NEAR END] is not cleared there-
fore can not perform ink cleaning.
• Be careful that if additional amount of remaining ink exceed the actual
remaining amount, prinitng continues even ink ended. Furthermore air enter
the ink tube which cause abonormal printting.
A guide of ink amount to add
STEPS:
1. When the ink level becomes low, [NEAR END]
is displayed.
(When ink ends, [INK END] is displayed)
2. Remove the ink cartridge and confirm the
weight of remaining amount of ink.
*Refer to the above table
3. To use the remaining ink, reinsert the ink car-
tridge.
4. Press the[ENTER] key.
If press the [END]key, it cancel the operation and return to
the LOCAL mode.
< LOCAL >
NEAR END - M - -
< LOCAL >
CARTRIDGE - M - -
ADD REMAIN ?
- M - -
ADD REMAIN
Yes : ent No : end
Ink cartridge weight Ink amount able to add
434g or below Do not add
435g - 444g + 10cc
445g - 454g + 20cc
Above 455g + 30cc
•To prevent missing some color or
vertical white line, weigh ink
cartridge correctly.
• This guide table is only a guide.
Be careful not to add too much ink.
Displayed alternately
- OPERATION MANUAL 1
- Foreword 3
- TABLE OF CONTENTS 5
- CHAPTER 3 Daily cleaning 6
- CHAPTER 4 Setting Function 6
- CHAPTER 5 Maintenance 7
- Setup Guide (separate volume) 9
- Display on the LCD 9
- Operation keys 9
- Example of pictorial signs 10
- Features 12
- For safe operation 14
- WARNING 15
- CAUTION 16
- CAUTIONS and NOTES 17
- Position of the warning label 18
- CHAPTER 1 19
- Before Use 19
- Moving the device 20
- Method of moving the device 21
- Locking/unlocking the casters 21
- Configuration and function 22
- The REAR 23
- Name Function 23
- Operation Panel 24
- Heater panel 25
- Carriage 26
- Capping station 27
- Pinch roller and Feed roller 27
- Media sensor 28
- Cutter blade and cutting line 28
- Media Size JV3-130SPII 31
- Setting the heater voltage 32
- MENU mode 33
- - 1.16 34
- CHAPTER 2 35
- Operation 35
- Switching on the power supply 37
- Cautions during operation 38
- 4 color ink set 39
- Adjusting the head height 40
- The error occurs 41
- Setting a roll holder 42
- 4. Fit the roll assembly 43
- - 2.14 48
- Operating the lock pin 49
- Setting the torque limiter 50
- - 2.18 52
- 4. Push down the clamp lever 52
- 5. Close the front cover 52
- 6. Press the [ENTER] key 52
- 7. Press the [ ] key 52
- Heater-Temperature control 53
- These two messages 54
- Normal pattern 55
- Abnormal pattern 55
- TEST & 56
- CLEANING 56
- CORRECTING PATTERN 57
- Display ink information 63
- Turning the power off 64
- CHAPTER 3 65
- Daily cleaning 65
- Routine Maintenance 66
- Cleaning the platen 67
- Cleaning the media sensor 67
- Wiper Cover 69
- Cleaning the head sides 70
- Use the cleaning kit 71
- CHAPTER 4 75
- Setting Function 75
- Basic operations of menus 76
- Function mode 78
- Setup functions 79
- MEDIACOMP. P. 2.24, A.6 80
- HEATER P. 2.19, 4.11, A.6 80
- PRINT MODE P. A.6 81
- INK LAYERS P. A.6 82
- DRYING TIME P. A.6 82
- AUTO CUT P. A.6 82
- PRIORITY P. A.6 82
- MARGIN P. A.6 83
- COLOR PATTERN P. A.7 83
- REFRESH P. A.7 83
- PRE-FEED P. A.6 83
- STOP TIME 86
- Effective Plotting Area 87
- Establishing An Origin 88
- - 4.16 90
- CHAPTER 5 91
- Maintenance 91
- Maintenance of the device 92
- [WIPER EXCHANGE] 95
- 8. Close the front cover 96
- 9. Press the [ENTER] key 96
- •Pipette 97
- • Glove, Goggle 99
- Out put direction 102
- - 5.13 103
- 5. Press the [ENTER] key 103
- 7. Press the [END] key twice 103
- Sleep cleaning [SLEEP clean] 107
- [FILL UP INK] 108
- [HEAD WASH] 108
- LOGICAL SEEK OFF: Media width 110
- < LOCAL > 110
- Plotting HEX CODE [DATA DUMP] 112
- Setting time [TIME SET] 114
- Replace the cutter blade 116
- A guide of ink amount to add 117
- Example of adding 20cc 118
- - 5.30 120
- CHAPTER 6 121
- Check the basic operation 123
- If image quality declines 124
- Ink cartridge trouble 125
- Error messages 129
- - 6.10 130
- APPENDIX 131
- Basic specifications 132
- Item JV3-130SL 133
- Specification for ink 134
- Function Flowchart 135
- FUNCTION Key : 136
- D201427-1.10-28032006 140
- Printed in Japan 142
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV3-130SPII
(292 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.669 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels