MIMAKI JV3-130SPII Spécifications Page 23
- Page / 142
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
- 1.5 -
The REAR
Name Function
1 Rear exhauster Discharges plotting smell from the media to out of the room.
2 Ink station Set the ink cartridges specified.
3 Ink cartridge Each cartridge contains ink of a specific color.
4
Cartridge protection cover
This cover is protect injuries, etc. due to protrusion of 440cc cartridge.
5Voltage selector switch Switches between 100-120 V and 200-240 V according to the power
voltage used.
6 IEEE-1394 connector A 400M bps interface connector compatible with IEEE-1394.
7 Parallel connector Bi-directional parallel interface connector (complies with IEEE1284)
8 Paper roll setting bar This bar facilitates a paper roll to be set in position.
9 Roll holder Roll holder is inserted in the right and left core of roll media to hold the
roll media. The roll holder is applicable to diameter of media cores with
2 and 3 inches. The attachment position (height) of the roll holder can
be set in three steps. To increase the heater contact time, attach it at
the bottom position.
10 AC inlet The power cable is connected to the AC inlet.
11 Main power switch Turns on/off the main power of the device. Leave the main power turned
on to prevent ink clogging.
12 Clamp lever Works together with the clamp lever on the font face of the device.
13 Preheater Preheat the media before plotting. ( Attached inside the platen )
1
7
6
8
2
10
11
9
5
12
13
3
4
- OPERATION MANUAL 1
- Foreword 3
- TABLE OF CONTENTS 5
- CHAPTER 3 Daily cleaning 6
- CHAPTER 4 Setting Function 6
- CHAPTER 5 Maintenance 7
- Setup Guide (separate volume) 9
- Display on the LCD 9
- Operation keys 9
- Example of pictorial signs 10
- Features 12
- For safe operation 14
- WARNING 15
- CAUTION 16
- CAUTIONS and NOTES 17
- Position of the warning label 18
- CHAPTER 1 19
- Before Use 19
- Moving the device 20
- Method of moving the device 21
- Locking/unlocking the casters 21
- Configuration and function 22
- The REAR 23
- Name Function 23
- Operation Panel 24
- Heater panel 25
- Carriage 26
- Capping station 27
- Pinch roller and Feed roller 27
- Media sensor 28
- Cutter blade and cutting line 28
- Media Size JV3-130SPII 31
- Setting the heater voltage 32
- MENU mode 33
- - 1.16 34
- CHAPTER 2 35
- Operation 35
- Switching on the power supply 37
- Cautions during operation 38
- 4 color ink set 39
- Adjusting the head height 40
- The error occurs 41
- Setting a roll holder 42
- 4. Fit the roll assembly 43
- - 2.14 48
- Operating the lock pin 49
- Setting the torque limiter 50
- - 2.18 52
- 4. Push down the clamp lever 52
- 5. Close the front cover 52
- 6. Press the [ENTER] key 52
- 7. Press the [ ] key 52
- Heater-Temperature control 53
- These two messages 54
- Normal pattern 55
- Abnormal pattern 55
- TEST & 56
- CLEANING 56
- CORRECTING PATTERN 57
- Display ink information 63
- Turning the power off 64
- CHAPTER 3 65
- Daily cleaning 65
- Routine Maintenance 66
- Cleaning the platen 67
- Cleaning the media sensor 67
- Wiper Cover 69
- Cleaning the head sides 70
- Use the cleaning kit 71
- CHAPTER 4 75
- Setting Function 75
- Basic operations of menus 76
- Function mode 78
- Setup functions 79
- MEDIACOMP. P. 2.24, A.6 80
- HEATER P. 2.19, 4.11, A.6 80
- PRINT MODE P. A.6 81
- INK LAYERS P. A.6 82
- DRYING TIME P. A.6 82
- AUTO CUT P. A.6 82
- PRIORITY P. A.6 82
- MARGIN P. A.6 83
- COLOR PATTERN P. A.7 83
- REFRESH P. A.7 83
- PRE-FEED P. A.6 83
- STOP TIME 86
- Effective Plotting Area 87
- Establishing An Origin 88
- - 4.16 90
- CHAPTER 5 91
- Maintenance 91
- Maintenance of the device 92
- [WIPER EXCHANGE] 95
- 8. Close the front cover 96
- 9. Press the [ENTER] key 96
- •Pipette 97
- • Glove, Goggle 99
- Out put direction 102
- - 5.13 103
- 5. Press the [ENTER] key 103
- 7. Press the [END] key twice 103
- Sleep cleaning [SLEEP clean] 107
- [FILL UP INK] 108
- [HEAD WASH] 108
- LOGICAL SEEK OFF: Media width 110
- < LOCAL > 110
- Plotting HEX CODE [DATA DUMP] 112
- Setting time [TIME SET] 114
- Replace the cutter blade 116
- A guide of ink amount to add 117
- Example of adding 20cc 118
- - 5.30 120
- CHAPTER 6 121
- Check the basic operation 123
- If image quality declines 124
- Ink cartridge trouble 125
- Error messages 129
- - 6.10 130
- APPENDIX 131
- Basic specifications 132
- Item JV3-130SL 133
- Specification for ink 134
- Function Flowchart 135
- FUNCTION Key : 136
- D201427-1.10-28032006 140
- Printed in Japan 142
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV3-130SPII
(292 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.332 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels