MIMAKI JV3-130SPII Spécifications Page 127
- Page / 142
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
- 6.7 -
< LOCAL >
DO TEST DRAW
NON-ORIGINAL INK
KMCY
The nozzle recovery cannot
be expected because the
device is left for a prolonged
period of time.
The loaded ink cartridge is
not MIMAKI genuine.
Make test plotting. If nozzle
missing is serious, execute
[STATION] - [WASH] for mainte-
nance.
Use the ink specified by
MIMAKI.
Warning message Cause Corrective measure
WRONG INK IC
KKMMCCYY
The IC chip of the ink car-
tridge cannot be read nor-
mally.
The type of the loaded ink
cartridge is different from the
previous one.
The color of the loaded ink
cartridge is different from the
previous one.
The loaded ink cartridge is
defective.
The ink cartridge is not
attached to the ink station.
Attach the ink cartridge(s)
corresponding with the color
shown on the display. If the
same error message appears
again on the LCD, contact your
local distributor to call for
service.
Check the type of the loaded
ink cartridge.
Check the color of the loaded
ink cartridge.
Check the loaded ink cartridge.
KIND OF INK
KMCY
INK COLOR
KMCY
WRONG CARTRIDGE
KMCY
NO CARTRIDGE
KMCY
Lower than print
guarantee TEMP.
Higher thanPrint
guarantee TEMP.
Attach the ink cartridge(s)
corresponding with the color
shown on the display.
The plotter is going to plot at
temperature which is out
of guarantee.
Change the temperature of the
installing environment.
When plotting without change,
pless the [ENTER] key.
- OPERATION MANUAL 1
- Foreword 3
- TABLE OF CONTENTS 5
- CHAPTER 3 Daily cleaning 6
- CHAPTER 4 Setting Function 6
- CHAPTER 5 Maintenance 7
- Setup Guide (separate volume) 9
- Display on the LCD 9
- Operation keys 9
- Example of pictorial signs 10
- Features 12
- For safe operation 14
- WARNING 15
- CAUTION 16
- CAUTIONS and NOTES 17
- Position of the warning label 18
- CHAPTER 1 19
- Before Use 19
- Moving the device 20
- Method of moving the device 21
- Locking/unlocking the casters 21
- Configuration and function 22
- The REAR 23
- Name Function 23
- Operation Panel 24
- Heater panel 25
- Carriage 26
- Capping station 27
- Pinch roller and Feed roller 27
- Media sensor 28
- Cutter blade and cutting line 28
- Media Size JV3-130SPII 31
- Setting the heater voltage 32
- MENU mode 33
- - 1.16 34
- CHAPTER 2 35
- Operation 35
- Switching on the power supply 37
- Cautions during operation 38
- 4 color ink set 39
- Adjusting the head height 40
- The error occurs 41
- Setting a roll holder 42
- 4. Fit the roll assembly 43
- - 2.14 48
- Operating the lock pin 49
- Setting the torque limiter 50
- - 2.18 52
- 4. Push down the clamp lever 52
- 5. Close the front cover 52
- 6. Press the [ENTER] key 52
- 7. Press the [ ] key 52
- Heater-Temperature control 53
- These two messages 54
- Normal pattern 55
- Abnormal pattern 55
- TEST & 56
- CLEANING 56
- CORRECTING PATTERN 57
- Display ink information 63
- Turning the power off 64
- CHAPTER 3 65
- Daily cleaning 65
- Routine Maintenance 66
- Cleaning the platen 67
- Cleaning the media sensor 67
- Wiper Cover 69
- Cleaning the head sides 70
- Use the cleaning kit 71
- CHAPTER 4 75
- Setting Function 75
- Basic operations of menus 76
- Function mode 78
- Setup functions 79
- MEDIACOMP. P. 2.24, A.6 80
- HEATER P. 2.19, 4.11, A.6 80
- PRINT MODE P. A.6 81
- INK LAYERS P. A.6 82
- DRYING TIME P. A.6 82
- AUTO CUT P. A.6 82
- PRIORITY P. A.6 82
- MARGIN P. A.6 83
- COLOR PATTERN P. A.7 83
- REFRESH P. A.7 83
- PRE-FEED P. A.6 83
- STOP TIME 86
- Effective Plotting Area 87
- Establishing An Origin 88
- - 4.16 90
- CHAPTER 5 91
- Maintenance 91
- Maintenance of the device 92
- [WIPER EXCHANGE] 95
- 8. Close the front cover 96
- 9. Press the [ENTER] key 96
- •Pipette 97
- • Glove, Goggle 99
- Out put direction 102
- - 5.13 103
- 5. Press the [ENTER] key 103
- 7. Press the [END] key twice 103
- Sleep cleaning [SLEEP clean] 107
- [FILL UP INK] 108
- [HEAD WASH] 108
- LOGICAL SEEK OFF: Media width 110
- < LOCAL > 110
- Plotting HEX CODE [DATA DUMP] 112
- Setting time [TIME SET] 114
- Replace the cutter blade 116
- A guide of ink amount to add 117
- Example of adding 20cc 118
- - 5.30 120
- CHAPTER 6 121
- Check the basic operation 123
- If image quality declines 124
- Ink cartridge trouble 125
- Error messages 129
- - 6.10 130
- APPENDIX 131
- Basic specifications 132
- Item JV3-130SL 133
- Specification for ink 134
- Function Flowchart 135
- FUNCTION Key : 136
- D201427-1.10-28032006 140
- Printed in Japan 142
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV3-130SPII
(292 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels