MIMAKI JV5-320S Spécifications Page 49
- Page / 130
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3-19
Establishing the Origin
Establishing the Origin
Establish the origin for printing the data on the media loaded on the printer.
When printing requires an area other than that defined by the established origin, set the origin at another point
by following the origin setting procedure again.
STEPS:
1 Once the media detection is completed, move the carriage and media using the JOG
keys [], [], [] and [] so that the carriage is located at the position where the
origin is to be established.
2 After determining the origin, press the [ENTER] key.
The printer displays the effective printing area, and then returns to LOCAL mode. (When the roll media is used,
the value in X direction is not displayed.)
From the time the printer starts next printing, it uses the origin that has been established here unless the origin
is newly established at another point.
When moving the origin to the back of the media, switch the moving direction as fol-
lows.
Origin
(Length)
L. ∗ > [JV5-01]
width : ∗∗∗∗ mm
ORIGIN SET UP
0.0 −−−−
Origin
(Width)
FEED DIRECTION SET
[ FORE FEED ]
ORIGIN SET UP : FORE
0.0 −−−−
ORIGIN SET UP : BACK
0.0 −−−−
FEED DIRECTION SET
[ BACK FEED ]
(Switch the direction)
(Move by the same direction key)
L. ∗ > [JV5-01]
width : ∗∗∗∗ mm
ORIGIN SET UP
0.0 −−−−
L. ∗ > [JV5-01]
width : ∗∗∗∗ mm
ORIGIN SET UP
∗ ∗ ORIGIN ∗ ∗
- OPERATION MANUAL 1
- Foreword 2
- TABLE OF CONTENTS 3
- CHAPTER 4 Daily Care 4
- CHAPTER 5 In Case of Trouble 4
- CHAPTER 1 7
- Safety Precautions 7
- Basic specifications 9
- 1 Safety Precautions 10
- Specifications for ink 11
- CHAPTER 2 13
- Before Use 13
- Configurations and Functions 14
- BL Light Blue 16
- Operation Panel 17
- 2 Press the [FUNCTION] key 18
- Outline of menu hierarchy 20
- Direct keys 22
- SET UP functions 23
- 2 Before Use 24
- MAINTENANCE functions 25
- MACHINE SET functions 28
- NCU functions 30
- CHAPTER 3 31
- Printing 31
- Adjusting the head gap 32
- Attach the platen sheet metal 34
- Remove the platen sheet metal 35
- 3 Printing 36
- Entry of right edge 41
- [ < ] or [ > ] key hit 41
- When the media left 41
- OK The media has wrinkles 42
- Adjust it 42
- [6]Set the media press 43
- For transfer paper 44
- Input of MediaLength 46
- MEDIA LENGTH = 50 m 46
- Clamp fixing spacer 47
- Media edge surface 47
- Effective Plotting Area 48
- Establishing the Origin 49
- Other notes 50
- Cut it using scissors etc 51
- Setting value : 52
- OFF, WEAK 52
- Little WEAK 52
- STANDARD, STRONG 52
- CHAPTER 4 53
- Daily Care 53
- Routine Maintenance 54
- 1 Pull the filter Assy out 55
- L. *> [JV5-01] 56
- ST.MAINTENANCE 56
- CARRIAGE OUT <ENT> 56
- COMPLETED <ent> 57
- * Being Initialized * 57
- PLEASE WAIT 57
- 4 Daily Maintenance 58
- CHAPTER 5 59
- In Case of Trouble 59
- Warning errors newly added 60
- Error messages newly added 60
- CHAPTER 6 61
- Operation for Functions 61
- Invoking SET UP functions 62
- Page in this 63
- (See P.6-28) 64
- INK LAYERS 66
- DRYING TIME 66
- PRE-FEED 67
- COLOR PATTERN 68
- DRYNESS FAN 68
- PRIORITY 69
- AUTO CLEANING 69
- Maintenance while printing 69
- (See P.3-2) 70
- List of functions 71
- 2 Press the [ST.MAINT] key 72
- [MEDIA RESIDUAL] 73
- L. ∗ > [JV5-01] 76
- FUNCTION 76
- MACHINE SETUP <ENT> 76
- REAR MIST FAN 77
- Feeding / TakeUP 77
- DRYNESS FEED 78
- CONFIRM. FEED 78
- PRE-FEED METHOD 78
- HEATER SETUP 78
- TIME SET 78
- UNIT SETUP 79
- STAMP SETUP 79
- CART. PRIORITY 80
- Test Draw Arrange 80
- MACHINE NAME 80
- Ambient temperature 80
- Serial&DealerNo 82
- NCU <ENT> 83
- Outline of the NCU functions 84
- NG JUDGEMENT (*1) 85
- COND.INDICATION 85
- DISPLAY setting 86
- Applied settings of functions 87
- Detailed settings of heaters 88
- Input range: 89
- PRE [OFF, 20 - 60] ° C 89
- POST [OFF, 20 - 70] ° C 89
- How to operate function menus 90
- Change is 91
- Functions related to ink 92
- JV5-320DS 94
- Function Flowchart [BOOT] 95
- 6 Operation for Functions 100
- CLtypeSetWithFUNCkey 109
- D202100-13-31102014 128
- Printed in Japan 130
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV5-320S
(166 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.251 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels