MIMAKI JV5-320S Spécifications Page 216
- Page / 298
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5 In Case of Trouble
5-24
∗∗∗∗ ERROR 160 ∗∗∗∗
NCU DETECT 02
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗ ERROR 160 ∗∗∗∗
NCU DETECT 03
An error occurred in the control sys-
tem.
Printing can be resumed after turning
off the nozzle missing detection func-
tion. Turn on the nozzle missing detec-
tion function again before starting to
print the next and subsequent print
files.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 160 ∗∗∗∗
NCU DETECT 04
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 161 ∗∗∗∗
NCU EXCHANGE
An error occurred in the control sys-
tem.
Operation can be resumed.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 161 ∗∗∗∗
NCU CONSUMPTION
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
Operation can be resumed after turning
off the nozzle missing detection func-
tion.
∗∗∗∗ ERROR 162 ∗∗∗∗
NCU LINE VOLTAGE
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 163 ∗∗∗∗
NCU SENSOR
An error occurred in the control sys-
tem.
Operation can be resumed.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 163 ∗∗∗∗
NCU SENSOR DETECT
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
Operation can be resumed after turning
off the nozzle missing detection func-
tion.
∗∗∗∗ ERROR 164 ∗∗∗∗
NCU FPGA ERROR
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 200 ∗∗∗∗
HEAD MEMORY (----)
An error occurred in the circuit board
system.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 201 ∗∗∗∗
BACKUP MEMORY
An error occurred in the circuit board
system.
∗∗∗∗ ERROR 201 ∗∗∗∗
BACKUP DATA
An error occurred in back-up data. The continued use is possible.
If the error message appears fre-
quently, please call for services.
∗∗∗∗ ERROR 202 ∗∗∗∗
DEVICE CONSTRUCTION
An error occurred in the control sys-
tem.
Contact your local distributor to call
for service.
Press the [ENTER] key to display the
details of the error. Press the [ENTER]
key again to enable the system to be
started after changing the configura-
tion to a supported one. (See 5-13)
Error message Cause Remedy
- OPERATION MANUAL 1
- Foreword 2
- DISCLAIMER OF WARRANTY 3
- Requests 3
- About media 4
- FCC Statement (USA) 4
- TABLE OF CONTENTS 7
- CHAPTER 4 10
- Daily Care 10
- CHAPTER 5 11
- In Case of Trouble 11
- CHAPTER 6 11
- Operation for Functions 11
- CHAPTER 1 13
- Safety Precautions 13
- Checking the accessories 14
- Features 16
- (See 1-8) 19
- Notes on Installation 20
- Notes on Location 21
- Moving the printer 22
- Connecting Power Supply 23
- WARNING 24
- Precautions in Use 25
- CAUTION 25
- CAUTIONS and NOTES 26
- Warning for Use 27
- CAUTIONS and NOTES 27
- Recommended types of media 28
- Warning labels 29
- 1 Safety Precautions 30
- Basic specifications 31
- Specifications for ink 33
- Notes on USB 2.0 Interface 34
- CHAPTER 2 37
- Before Use 37
- Configurations and Functions 38
- 2 Before Use 40
- Bottom (Connector) 41
- 2 Press the [ENTER] key once 42
- When water-based ink is used 44
- Cartridge control 45
- Carriage 47
- Capping station 47
- Cutter blade and cutting line 48
- Media sensor 48
- Feed roller 49
- Clamp lever 49
- Operation Panel 52
- How to read the display 53
- Job processing status 54
- Message indicating status 54
- How to use the keys 56
- Functions of the JOG keys 57
- Modes and Menu Screens 58
- About Function Menus 59
- 2 Press the [FUNCTION] key 60
- Outline of menu hierarchy 62
- Direct keys 64
- SET UP functions 65
- MAINTENANCE functions 67
- MACHINE SET functions 70
- NCU functions 72
- CHAPTER 3 73
- Printing 73
- Operation flow 74
- Turning the power on 75
- Power Switches 76
- Adjusting the head gap 77
- 3 Press the [END] key 78
- Tension-bar (Grip this part) 81
- 2.Remove the holders 82
- Lock screw 83
- Adjust screw 83
- Ratchet handle 84
- Roll holder 84
- Obverse side print (Face in) 85
- Reverse side print (Face out) 85
- [3] Adjust the media 88
- 1 Open the front cover 88
- Face out 93
- Tension-bar 94
- No. Operation Outline 95
- 1 Set the operation panel 96
- Media support bar 97
- Tighten the screw 100
- Media Press 101
- 3 Printing 102
- Input of MediaLength 104
- MEDIA LENGTH = 50 m 104
- Torque limiter 105
- Pinch roller 106
- 5 Press the [ENTER] key 107
- How to select a user type 109
- How to check the user type 109
- Operating the heaters 110
- 2 Press the [HEATER] key 111
- What is beading ? 112
- Temperature adjustment 113
- Heater Power OFF PRE PRT AFT 114
- THERM ∗∗ °C ∗∗ °C 114
- PRE PRT AFT 114
- BREAK ∗∗ °C ∗∗ °C 114
- [PG DROP ADJUST.] 115
- 6 Press the [ENTER] key 116
- Abnormal pattern 117
- Normal pattern 117
- 2 Press the [CLEANING] key 118
- 4 Press the [ENTER] key 121
- CORRECTION PATTERN 122
- Correction value: 123
- -255 ~ 255 123
- Correction value is too large 123
- OverlapClearance 123
- Correction value is too small 123
- Effective Plotting Area 126
- Establishing the Origin 127
- R. ∗ +> 720x1080 .12 129
- Bd. Vd. x1. 1L : ∗∗.∗∗ m 129
- 3 Press the [ENTER] key 132
- 2 Press the [] key 133
- Automatic cleaning 134
- 4 Press the [FUNCTION] key 135
- (Sb51) is used) 136
- When setting to WIPING 138
- [INK NEAR END] 139
- [INK END] 139
- [INK END][INK NEAR END] 140
- 2 Press the [ENTER] key 141
- Turning the power off 142
- Routine Maintenance 144
- Notes on cleaning solution 145
- Cleaning exterior surfaces 145
- Cleaning the platen 145
- Cleaning the media press 146
- Opening the maintenance cover 147
- Frame axis 148
- L. ∗ > [JV5-01] 149
- ST.MAINTENANCE 149
- CARRIAGE OUT <ent> 149
- COMPLETED :end 151
- ∗Being Initialized∗ 151
- PLEASE WAIT 151
- 7 Press the [ENTER] key 153
- 11Press the [ENTER] key 154
- To step 5 To step 11 161
- PUMP tube cleaning 164
- Wiper cleaning 166
- [CR.MAINTENANCE] 168
- 9 Press the [ENTER] key 169
- Input range: OFF, 1 to 168 171
- Other maintenance functions 179
- 10/10 - 1/10 180
- WIPER LEVEL 180
- LEVEL : 10/10 180
- [BOX EXCHANGE LV] 181
- L .1 > [ JV5-01 ] 182
- ! WasteTANK FULL/NONE 182
- ! NearFULL WASTE TANK 182
- Cleaning of Flushing Box 184
- 3 Open the pump cover T 185
- [CARRIAGE OUT] is displayed 188
- 3 Open the front cover 190
- Roller of cutter unit 191
- 4 Daily Maintenance 192
- Power does not turn on 194
- Check the basic operation 195
- If image quality is poor 196
- (jet deviation) 197
- [DISCHARGE&WASH] 198
- 4 Remove the ink cartridges 199
- 5 In Case of Trouble 202
- Ink cartridge trouble 204
- Warning messages 207
- Error messages 211
- 6 Operation for Functions 220
- Invoking SET UP functions 221
- Set the printing conditions 222
- (See 3-50) 223
- (See 6-33) 223
- PRINT MODE 224
- INK LAYERS 226
- DRYING TIME 226
- AUTO CUT 227
- PRE-FEED 227
- COLOR PATTERN 228
- PRIORITY 229
- (See 3-62) 230
- (See 3-64) 230
- (See 3-5) 230
- SETUP RESET 231
- List of functions 232
- 2 Press the [ST.MAINT] key 233
- [MEDIA RESIDUAL] 234
- Setting a MACHINE SETUP 237
- Feeding / TakeUP 238
- DRYNESS FEED 238
- CONFIRM. FEED 238
- PRE-FEED METHOD 238
- HEATER SETUP 238
- MEDIA CUT 239
- TIME SET 239
- UNIT SETUP 239
- STAMP SETUP 240
- Detection of media 241
- MACHINE NAME 241
- INFORMATION 241
- ERROR HISTORY 241
- MAINTE. HISTORY 241
- PRT.modeHISTORY 242
- When solvent ink is used 243
- Serial&DealerNo 245
- Invoking NCU functions 246
- Outline of the NCU functions 247
- NG JUDGEMENT (*1) 248
- COND.INDICATION 248
- DISPLAY setting 249
- Applied settings of functions 250
- Detailed settings of heaters 251
- Input range: 252
- PRE [OFF, 20 - 60] ° C 252
- PRT [OFF, 20 - 60] ° C 252
- AFT [OFF, 20 - 70] ° C 252
- How to operate function menus 253
- Change is 255
- Functions related to ink 256
- Function Flowchart [BOOT] 258
- Sb51 is used 268
- LEFT:ONx1 RIGHT:ON 268
- DECIDE = [ENTER] 270
- TIMER SET = [FUNC.] 270
- INPUT RANGE 271
- 0 - 60min, CONTINUE 271
- [1] VACUUM 271
- STOP TIMER :0min 271
- 0 to 60min/CONTINUE 271
- D201703-14-18042008 296
- Printed in Japan 298
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV5-320S
(156 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.889 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels