MIMAKI JV5-320S Spécifications Page 55
- Page / 298
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-19
Operation Panel
How to read the LED indications
The LEDs light up to indicate the status of the printer as described below.
Heater Name Name Function
--
BUSY lamp
Lights up when the printer is currently executing some processing.
While this lamp is lit, never open any cover of the printer and never
operate any key; otherwise, the printer may develop trouble.
--
HEAT SW lamp Lights up orange when power to the heater is turned on.
Pre-heater
HEAT lamp Lit orange while the pre-heater is in heating operation.
CONSTANT lamp
Lights up green when the temperature of the pre-heater reaches the
preset temperature.
Print heater
HEAT lamp Lit orange while the print heater is in heating operation.
CONSTANT lamp
Lights up green when the temperature of the print heater reaches the
preset temperature.
Post-heater
HEAT lamp Lit orange while the post-heater is in heating operation.
CONSTANT lamp
Lights up green when the temperature of the post-heater reaches the
preset temperature.
Print heater
BUSY lamp
Pre-heater
HEAT SW lamp
Post-heater
- OPERATION MANUAL 1
- Foreword 2
- DISCLAIMER OF WARRANTY 3
- Requests 3
- About media 4
- FCC Statement (USA) 4
- TABLE OF CONTENTS 7
- CHAPTER 4 10
- Daily Care 10
- CHAPTER 5 11
- In Case of Trouble 11
- CHAPTER 6 11
- Operation for Functions 11
- CHAPTER 1 13
- Safety Precautions 13
- Checking the accessories 14
- Features 16
- (See 1-8) 19
- Notes on Installation 20
- Notes on Location 21
- Moving the printer 22
- Connecting Power Supply 23
- WARNING 24
- Precautions in Use 25
- CAUTION 25
- CAUTIONS and NOTES 26
- Warning for Use 27
- CAUTIONS and NOTES 27
- Recommended types of media 28
- Warning labels 29
- 1 Safety Precautions 30
- Basic specifications 31
- Specifications for ink 33
- Notes on USB 2.0 Interface 34
- CHAPTER 2 37
- Before Use 37
- Configurations and Functions 38
- 2 Before Use 40
- Bottom (Connector) 41
- 2 Press the [ENTER] key once 42
- When water-based ink is used 44
- Cartridge control 45
- Carriage 47
- Capping station 47
- Cutter blade and cutting line 48
- Media sensor 48
- Feed roller 49
- Clamp lever 49
- Operation Panel 52
- How to read the display 53
- Job processing status 54
- Message indicating status 54
- How to use the keys 56
- Functions of the JOG keys 57
- Modes and Menu Screens 58
- About Function Menus 59
- 2 Press the [FUNCTION] key 60
- Outline of menu hierarchy 62
- Direct keys 64
- SET UP functions 65
- MAINTENANCE functions 67
- MACHINE SET functions 70
- NCU functions 72
- CHAPTER 3 73
- Printing 73
- Operation flow 74
- Turning the power on 75
- Power Switches 76
- Adjusting the head gap 77
- 3 Press the [END] key 78
- Tension-bar (Grip this part) 81
- 2.Remove the holders 82
- Lock screw 83
- Adjust screw 83
- Ratchet handle 84
- Roll holder 84
- Obverse side print (Face in) 85
- Reverse side print (Face out) 85
- [3] Adjust the media 88
- 1 Open the front cover 88
- Face out 93
- Tension-bar 94
- No. Operation Outline 95
- 1 Set the operation panel 96
- Media support bar 97
- Tighten the screw 100
- Media Press 101
- 3 Printing 102
- Input of MediaLength 104
- MEDIA LENGTH = 50 m 104
- Torque limiter 105
- Pinch roller 106
- 5 Press the [ENTER] key 107
- How to select a user type 109
- How to check the user type 109
- Operating the heaters 110
- 2 Press the [HEATER] key 111
- What is beading ? 112
- Temperature adjustment 113
- Heater Power OFF PRE PRT AFT 114
- THERM ∗∗ °C ∗∗ °C 114
- PRE PRT AFT 114
- BREAK ∗∗ °C ∗∗ °C 114
- [PG DROP ADJUST.] 115
- 6 Press the [ENTER] key 116
- Abnormal pattern 117
- Normal pattern 117
- 2 Press the [CLEANING] key 118
- 4 Press the [ENTER] key 121
- CORRECTION PATTERN 122
- Correction value: 123
- -255 ~ 255 123
- Correction value is too large 123
- OverlapClearance 123
- Correction value is too small 123
- Effective Plotting Area 126
- Establishing the Origin 127
- R. ∗ +> 720x1080 .12 129
- Bd. Vd. x1. 1L : ∗∗.∗∗ m 129
- 3 Press the [ENTER] key 132
- 2 Press the [] key 133
- Automatic cleaning 134
- 4 Press the [FUNCTION] key 135
- (Sb51) is used) 136
- When setting to WIPING 138
- [INK NEAR END] 139
- [INK END] 139
- [INK END][INK NEAR END] 140
- 2 Press the [ENTER] key 141
- Turning the power off 142
- Routine Maintenance 144
- Notes on cleaning solution 145
- Cleaning exterior surfaces 145
- Cleaning the platen 145
- Cleaning the media press 146
- Opening the maintenance cover 147
- Frame axis 148
- L. ∗ > [JV5-01] 149
- ST.MAINTENANCE 149
- CARRIAGE OUT <ent> 149
- COMPLETED :end 151
- ∗Being Initialized∗ 151
- PLEASE WAIT 151
- 7 Press the [ENTER] key 153
- 11Press the [ENTER] key 154
- To step 5 To step 11 161
- PUMP tube cleaning 164
- Wiper cleaning 166
- [CR.MAINTENANCE] 168
- 9 Press the [ENTER] key 169
- Input range: OFF, 1 to 168 171
- Other maintenance functions 179
- 10/10 - 1/10 180
- WIPER LEVEL 180
- LEVEL : 10/10 180
- [BOX EXCHANGE LV] 181
- L .1 > [ JV5-01 ] 182
- ! WasteTANK FULL/NONE 182
- ! NearFULL WASTE TANK 182
- Cleaning of Flushing Box 184
- 3 Open the pump cover T 185
- [CARRIAGE OUT] is displayed 188
- 3 Open the front cover 190
- Roller of cutter unit 191
- 4 Daily Maintenance 192
- Power does not turn on 194
- Check the basic operation 195
- If image quality is poor 196
- (jet deviation) 197
- [DISCHARGE&WASH] 198
- 4 Remove the ink cartridges 199
- 5 In Case of Trouble 202
- Ink cartridge trouble 204
- Warning messages 207
- Error messages 211
- 6 Operation for Functions 220
- Invoking SET UP functions 221
- Set the printing conditions 222
- (See 3-50) 223
- (See 6-33) 223
- PRINT MODE 224
- INK LAYERS 226
- DRYING TIME 226
- AUTO CUT 227
- PRE-FEED 227
- COLOR PATTERN 228
- PRIORITY 229
- (See 3-62) 230
- (See 3-64) 230
- (See 3-5) 230
- SETUP RESET 231
- List of functions 232
- 2 Press the [ST.MAINT] key 233
- [MEDIA RESIDUAL] 234
- Setting a MACHINE SETUP 237
- Feeding / TakeUP 238
- DRYNESS FEED 238
- CONFIRM. FEED 238
- PRE-FEED METHOD 238
- HEATER SETUP 238
- MEDIA CUT 239
- TIME SET 239
- UNIT SETUP 239
- STAMP SETUP 240
- Detection of media 241
- MACHINE NAME 241
- INFORMATION 241
- ERROR HISTORY 241
- MAINTE. HISTORY 241
- PRT.modeHISTORY 242
- When solvent ink is used 243
- Serial&DealerNo 245
- Invoking NCU functions 246
- Outline of the NCU functions 247
- NG JUDGEMENT (*1) 248
- COND.INDICATION 248
- DISPLAY setting 249
- Applied settings of functions 250
- Detailed settings of heaters 251
- Input range: 252
- PRE [OFF, 20 - 60] ° C 252
- PRT [OFF, 20 - 60] ° C 252
- AFT [OFF, 20 - 70] ° C 252
- How to operate function menus 253
- Change is 255
- Functions related to ink 256
- Function Flowchart [BOOT] 258
- Sb51 is used 268
- LEFT:ONx1 RIGHT:ON 268
- DECIDE = [ENTER] 270
- TIMER SET = [FUNC.] 270
- INPUT RANGE 271
- 0 - 60min, CONTINUE 271
- [1] VACUUM 271
- STOP TIMER :0min 271
- 0 to 60min/CONTINUE 271
- D201703-14-18042008 296
- Printed in Japan 298
Produits connexes et manuels pour Imprimer et scanner MIMAKI JV5-320S
(156 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.210 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels